2N7269 DATASHEET PDF
n Light Weight. For footnotes refer to the last page. IRHM REF: MIL-PRF- / TOAA. This datasheet has been downloaded. 2N 2NU. JANSR (K RAD(Si)). JANSF (K RAD(Si)). ABSOLUTE MAXIMUM RATINGS (TC = +25°C unless otherwise noted). Parameters / Test. 2N datasheet, 2N pdf, 2N data sheet, datasheet, data sheet, pdf, Microsemi, N-Channel.
|Published (Last):||15 February 2011|
|PDF File Size:||3.54 Mb|
|ePub File Size:||1.29 Mb|
|Price:||Free* [*Free Regsitration Required]|
The matte-tin plating shall contain no more than 0 05 percent by weight codeposiled organic material measured as elemental carbon Minimum lead content shall be 3 percent.
The device type Tkwber shall be es specified in the associated detail spec l f Ication or SO the numbers Shall consist o’ two digits atsiprwd saquant ially, froa 01 to W within each associatad detail specification or SMC.
Thickness shall be 2 54 2n72269 to micromches 7. Detailed finish requirements for each of the electrical parts. Where space is critical, the low profile CLP component should be considered, but at the expense of some reduction in electrical Q. The P IN shell be as shown in the following exaaple: Magnetics No Yes 3. Summary of the plating requirements for electrical components and risk assessment.
The datwsheet of this report is to review and document the electrical and mechanical part requirements to identify any risk of having a pure tin datasbeet on any of these parts.
Materials and Manufacture 4. Foftowmg too sufder dHi retmning process the etectncai measurements required hi group A subgroup ” pnrcenl screening test Stiafi be repeated on percent of tori lol. The part leads can be identified as gold from the DPA color photographs. The Ferrite is not coated.
2N Datasheet pdf – N-Channel – Microsemi
The termination finish is identified by a single letter as follows: C, C Types A, ft. The following DPA photograph shows gold plated datasjeet and leads.
Items do not have a finish. If hermetic seal is required in the group A, subgroup 1 tests, this test shall be repeated, see 4. Thickness shall be 7.
The thickness shall be 7 62 pm to microinches C – Hot solder daatsheet 60 microinch minimum.
【2N7269 IR】Electronic Components In Stock Suppliers in 2018【Price】【Datasheet PDF】USA
Capacitors covered by this specification are classified by style as specified see 3 1 1. The intent of this report is to identify any electrical, electromechanical or mechanical part that does not have adequate requirements to prevent the use of a pure tin finish.
The matte-tin plating shall contain no more than 0. Description Part Value 1. The lead finish and restrictions on the case material are defined in the following paragraphs of the SCD: Search the history of over billion web pages on the Internet. Mil-M defines finish A as hot solder dip.
For explanation satasheet superscript codes following XXXX. The lead finish is defined in the Standard Military Drawing as the last letter of the part number. Use of tin- lead Sn-Pb finishes are acceptable provided that the minimum lead content is 3 percent. Length jt controls the operating frequency. Parts procured to a Military Specification with a QML listing qualified parts that have a statement that prohibits the use of pure tin and defines the finish as part of the part number in 2nn7269 Military Specification.
A pure tin finish is not prohibited. However, Motorola is aware that, on some other programs, parts with pure tin finish have been identified, even though, the requirement for no tin finish was imposed.
Component List  page :: Oxygen Electronics, LLC
Tin-lead Sn-Pb finishes are acceptable provided that the minimum lead content is three percent see 6. External metallic package elements including leads and terminals shall meet the applicable environmental requirements without additional finishing or shall be finished with a coating which conforms to one of the options listed in H4 3 and table Dahasheet.
Mil- M is the controlling document for device class M, B and S. The materials and coatings Shill be datasheeh specified f toe 3. The type of insulation consists of a two digit codes The type will be defined on the specificationsheet.
Lead freiaa or terminal Material end finish ahet.