CONFIGURATION ROUTAGE STATIQUE CISCO PDF

May 23, 2020 By:

Les routeurs Cisco et IOS. Configuration de la route par défaut. En mode configuration ip route adrIPReseau masque adrIPGateway route statique. Le pare-feu VPN sans fil N Cisco RVW comprend: la prise en charge du routage statique, versions RIP (Routing Information Protocol) 1 et 2 et du routage. CONFIGURATIONS LINUX Vérifiez que ROUTEUR CISCO IOS: a , ROUTEUR QUAGGA A interface.

Author: Tazilkree Grozil
Country: Kuwait
Language: English (Spanish)
Genre: Career
Published (Last): 17 August 2010
Pages: 151
PDF File Size: 11.14 Mb
ePub File Size: 18.78 Mb
ISBN: 133-7-57611-203-9
Downloads: 77430
Price: Free* [*Free Regsitration Required]
Uploader: Yozshunris

This Article Applies to: IP subnet mask for this net segment is Static route tells the device exactly where to send traffic, no matter what. In fact, R0 can successfully ping R1 right after adding the static route to R0 Administrative distance of a static route.

Subscription TP-Link takes your privacy seriously. No Install —Do not install the route in either route table. The administrative distance can be manually re configured so that the static route can be configured as a backup route, to be used only if the dynamic route is unavailable.

The commands to add a static route are as follows: To route IP traffic destined for the network Suppose that your company has 2 branches located in New York and Chicago. Business Wireless Takes your enterprise Wi-Fi to new levels. The router treats a configugation route pointing to an interface the same as a connected interface so the its AD is 0.

  AS VOLTAS QUE A VIDA D ZIBIA GASPARETTO PDF

Discard —Select to drop packets that are addressed to this destination. So there are 2 networks that are directly connected to R0: IP subnet mask for this address configudation R0 config ip route Input destination network, subnet mask, default gateway, select status and save it.

Configure a Static Route

Click here to contact TP-Link technical support. Please turn it on for the best experience.

And RIP has an administrative distance of Multicast —Install the route in the multicast route table available for IPv4 routes only. Powerline Adapter Transforms electrical wiring to carry the network signal. Thank you We appreciate your feedback.

Now try to ping each far end network Note: Static routing can also be used in stub networksor to provide a gateway of last resort.

Static routing

Static routing and dynamic routing are not mutually exclusive. Dynamic routes, on the other hand, use a routing protocol to configuraton the best path and the routes can be changed depending on specific parameters like bandwidth, delay, cost….

Rouhage 4 Click Add New…. Your feedback helps improve this site. The gateway of PC is router2 which connected the Internet, but when PC visit servers in intranet, firstly the request will be sent to router2. Static route and Dynamic route Static route tells the device exactly where to send traffic, no matter what.

  KULT RUMOURS PDF

The administrative distance is a measure of trustworthiness where lower numbers are considered to be more trustworthy than higher numbers.

All roytage with unsourced statements Articles with unsourced statements from December Configure a Static Route. In most Linux distributions, a static route can be added using the iproute2 command.

Exercice de routage statique IPv4 et IPv6 en Cisco IOS

Directly connected routes have an administrative distance of 0. Sign Up Follow Cisoc www. With dynamic routes, routers can communicate with each other to exchange routing information. After careful consideration you decided to connect them via static route. In fact, R0 can successfully ping R1 right after adding the static route to R0.

Static routing can have some potential disadvantages: IGRP has an administrative distance of The simple syntax of static route: Perform the following task to configure Static Routes or a default route for a virtual router on the firewall. Static Route Overview Static Route Overview If you decide that you want specific Layer 3 traffic to take a certain route without participating in IP routing protocols, you